Introduction


General iOS iDevice (iPhone & iPad & iPod &iWatch and MacBook)

  • -Support all iOS iDeivce read general information
  • -Support super Restore & Update & Custom flash IPSW
  • -Automatic iOS version detecting, Even in disabled or untrust mode
  • -Support multi iDevice operating in same time
  • -History recording by Real-time logs
  • -Support all iDevice Debug Mode do button Testing
  • -Support all iOS iDeivce Activate / Deactivate by USB cable
  • -Support install iOS Apps from IPA package
  • -Support management user's  / system and Archives Apps
  • -Support Update、Install、Uninstall、Backup Apps by one button
  • -Support iWatch repair / Update/ Restore by iBus Cable
  • -Support all iOS iDeivce mode change by USB cable
  • -Support all iOS iDeivce iCloud Status Check (Black/White List)
  • -Support one button Bypass iPhone 4 iCloud Account
  • -Support all iOS iDeivce Recovery iCloud Data (IPR)
  • -Support all iOS iDevice Recovery email access (IPR)
  • -Support all iOS iDevice read the Restrictions access (IPR)
  • -Support all iOS iDeivce diagnostics check by USB cable
  • -Support all iOS iDeivce time setting by USB cable (beta)
  • -Support all iOS 7.x iDevice screen passcode unlock (4 digits)
  • -Support all iOS 7.x iDevice permanently disabled remove
  • -Support all iOS 8.0 - 8.11 iDevice screen passcode Unlock (4 digits) if your iDevice temporarily disabled or not disable yet
  • -Support all apple MacBook Model unlock 4 digits by EFI Boot Mode
  • -Support all apple MacBook Model unlock 4 digits iCloud PIN

 

Introduction


iOS Jailbreak iDevice (OpenSSH Required - iOS 6.0 - 8.4)

    • -Support Read 4 digits passcode (Many deivce be same time)
    • -Support jailbreak  statue check
    • -Support using cable detect data via SSH
    • -Support fast bruteforce SSH passcode
    • -Support one button open SSH Tunnel
    • -Support one button read iCloud Account
    • -Support one button delete iCloud Account
    • -Support Change Phone general / About info (Model & Color etc)
    • -Support hide / Show Application icon
    • -Support all iOS Super Backup

 

Samsung & HTC & HuaWei Mobile Models

    • -All Samsung & HTC Android based Mobie (V4.3+ - 4 Pin Lock Unlock)
    • -All Huawei Android Mobile Hisilicon based Unlock

 

System Requirements

    • -All Windows 7, Windows 8/8.1 or Windows 10

 

Responsibility

    • This tool is only for personal study and research purposes, please do not used for commercial purposes, do not do anything illegal things, otherwise you need take all responsibility.

Create & Active account

Register an account

① First you must Register an account on official website with valid Email.


Once you done, you will got this message:

You have successfully registered. Please check your email for further information!

Verify your account

② Verify your account withToken code (This code will be received by email)


A. Go to your email inbox. you will got this :

B. Input your registered email and the Token code to activate your account:

Login to website

③ Once your account activated, then you can go to login page access to site.

If you lost your passcode you can using "Lost passcode" function to find the passcode back. The related code will be send to you by register email

Activation MFC Dongle

To activation your dongle you have to know your Dongle serial number at first, to get the serial number info you can following this.

A. Normally On MFC Dongle Plastic Package with a barcode that is the Serial Number (0xXXXXXXXX)

B. If you using old version then connect dongle to computer, Run Software and Press "Update" you will get the serial number

C. If you using new version then connect dongle to computer, Run Software and open MFC Tools Tab, Press "Read SN" button, you will get the serial number from logs.


Activation page

Now go to User Dashboard and at Activation Dongle tab , input MFC Serial number, Press "Activating Now" button to active your dongle.

Download & Install

Download software

Go to download page to get software and install it. [ Due customer computer have different antivirus software, You may close before then install and add that into trust list. ]

Install software

① When you finish downloaded the sfotware from download page , Now start to install it. The installing will be automatic finish once get your confirm during in procedure.

Install software

② The software will installing to C:/MFC, you can change the path to D:/MFC etc. but the folder path must be like this (C:/MFC or D:/MFC) otherwise maybe not work.
Install software

  ③ Continue installing
Install software

  ④ During installing the drivers will be automatic installed. just press "next" button let it automatic finish. (Installed path C:/MFC/Driver/DongleDrivers)

Install software

⑤ Driver Installing... (Installed path C:/MFC/Driver/MicrosoftRedistributables. For windows 7, if you have Dll error, you have to manually install both driver  ["vcredist_x64.exe" / "vcredist_x86.exe"] in this folder again. )

Install software

⑥ Software install Done.
About INSTALL FAQ:

Got mfc120.dll ,mfc120u.dll and libusb0.dll error ?

a, Install Drivers from DongleDrivers directory (C:/MFC) by running InstallDriver.exe This will installing mfc120.dll & mfc120.dll required for the program to start.

b, Install vcredist_x86 or vcredist_x64 for windows from MicrosoftRedistributables directory (Win 7 Need install Both)

c, Frist time to use software you need Connect MFC in BOOT MODE. This will installing libusb0.dll driver required for the program to start.

 

We encourage all customers always to upgrade the spftware to the latest version , When the new version released on official website , the old version will be expired after few days. Once software expired you can not use that anymore.


How to test 3 in 1 data cable ?

a, Update MFC Dongle using iOS 7 Auto V2.2

b, Using a normal iPhone mobile, open Notes and add a New content

d, Connect the 3 in 1 data cable to mobile USB port

e, Connect the MFC Dongle to 3 in 1 data cable OTG port

After finish those steps, the phone keypad will be auto disappeared (if not disappear mean's cable problem), and will be display 0000 codes in the content etc. this mena the 3 in 1 data cable working prefectly. but for iOS 8.x Device, if repeatedly plug the cable to device that may not recognize the cable all the time. in this case, please keeep the cable connected and manualy reboot device.

MFC Dongle BOOT MODE - First time using dongle you have to do this.
About MFC Normal & Boot Mode
  • NORMAL MODE for settings / Sensor test / Read code etc.
  • BOOT MODE for update & repair. Put P0 &GND pin together.

View the details in device manager

If everything setup correctly you will see like this

About "USB not Recognize" issue ?

a. Be sure when you input the dongle to computer using the adatpor (the black one or the old one with kingston logo) and don't put the dongle to this adaptor in backwards. Don't put only MFC dongle to computer direct or using some USB hub or extension usb cable etc.

b. we are strongly recommend customer using computer with USB 2.0 port.

c. Don't touch the IC's on MFC dongle when you do any operation, Keep away from any metallic conductor to avoid Short Circuit

d. Don't try it on old PC/laptop (the USB maybe very bad already), we recommend use new PC /laptop

e. When update dongle, Using boot mode, Don't attach any accessories

 

One of a to e condition can casing the "USB not Recognize" issue then your computer can not detect dongle anymore.

 


PS: During update and write function will not damage the dongle , Even you take out the dongle when you action, but this may casing "USB not Recognize" issue too, If this is happened just update again.

If all steps can not fix your issue and dongle still under warranty,  you contact your reseller ask for exchange (This may cost you some shipping fee ).

Operation Guide

How to Start and do related settings:

Sensor<->Connection<->MFC Dongle (How to connect ?) Check page 20 21 22

Sensor is very important part for MFC Dongle when you are unlocking your device. The sensor is measuring the brightness value of your device screen during unlocking, Once unlocking done your device screen will be change and that will activation MFC Dongle LEDs get fast blinking mode.

 

Sensor position and covering is very important ,it might stop the unlock process before finding the correc code (usually if the external light influences the light sensor)

 

About the sensor testing ?

A. To see if the sensor is working just press sensor checkbox On the MFC Software and watch if the sensor values change. If you put the sensor in dark/black & White place ( for example holding in your hand (Or Phone Lock Screen dark area), the value must be lower or 0 and if you put the sensor direct towards a powerful light (White screen or Emergency screen)the value must be higher 100 to 500. This is how you can test the sensor easily.B. Update MFC Dongle with "Test iPower" , then connect sensor and ipower to MFC Dongle, Input that to Computer USB port. If you put the sensor in dark/black place ( for example holding in your hand (Or Phone Lock Screen dark area), Deivce LEDs will no binking, Otherwise will be fast blinking once sensor detecting light.

[*]Old sensor is 10k ohm Chip resistor, marked 1001
[*]New sensor is 20k ohm Chip resistor marked 2002 (Suggest use New Sensor)

Sensor Connections:
A. Sensor Connections without iPower Adaptor

This connections For iOS 7.x iDevice and MacBook / Samsung / HTC etc

B. Sensor Connections with iPower Adaptor

This connections For iOS 8.x iDevice

3 in 1 OTG cable Micro USB no charging function

The 3 in 1 cable connections

MAIN INTERFACE EXPLANATION:

Support Modle & Tool Select Tab

Only iMFC function requiring access authority.

Login Informations:

This using same access details which you registed on mfcbox.com.

If you changed passcode on mfcbox.com, Software will be recognizes the new passcode after 5 mins

Access authority will be requiring you again after 24hs .

Logs information:

Here will be show some related operation logs.

Dongle Connection Status & Serial Number:

This Status showing : NOT CONNECTED | NORMAL | BOOT

Modes Using For:

NORMAL for settings / Sensor test / Read code etc.

BOOT for update and repair.

BOOT MODE you need to connect P0 and GND(P zero) pin together. Check Here For the details.

Serial Number:

Current Dongle Serial Number, Eg. 0xXXXXXXXX.

Don't share anything related aboout the serial number informations to others.

Tab login logs Status
What we need pay attention for MFC Software:

A. I had register an account on mfcbox.com but still can not login ?

1.Be sure your internet already connected.

2.Be sure you already activated your dongle on mfcbox.com

3.Checking software detected dongle serial number or not, if not you can do this:

  • Go to MFC Tools Tab "Read SN" (Sometime you need put dongle in boot mode)
  • Or under iDevice Tab press "Update" checkbox then input the dongle

4.Be sure you are using the latest software version (Once new version released old version will be expired in few days)

5.Due some reason, your account got blocked. Contact our team unblock that by email (support@mfcbox.com)


B. Can i using "A" dongle account using for "B" dongle ?

No, You can not , that will not allow you open IMFC tab, So different dongle must with different account on mfcbox.com.


C. How can i know ready to use?

1."iMFC" tab be able to open.

2.You got this logs on software "[user][info] iDevice module is ready! Please make sure MFC dongle is still connected!".

D. i forget my login password ?

if you forget your password, you need go to Lost Password page reset your passcode by Username and Email Address.


E. Where to change my password ?

if you want to change your password, you need go to Manage Profile page to do this. After password changed , you have to waiting 5 mins than can login into MFC Software.


F. Can i change my serial number ?

Yes, you can . To do this you must provide some related proof to our team by email (support@mfcbox.com), and this will taking 1-3 days to get confirm.


Important: Please don't share your account to others, and don't post your dongle serial numer on public internet etc .

INTERFACE EXPLANATION FOR iOS 7.x :

Modle & Tool Select Tab

To Unlock iOS 7.x iDevice we must choose iDevice Tab.

Operations Options:

Each options have operation guide inside the software, Read before unlock Device

The different between V2.2 V2.3 V2.4

  • V2.3 Can auto adjust the screen brightness if sensor detecting the screen brightness very low
  • V2.4 has been separated the 20 codes function.

 

Write Function:

Can customize your settings later or just keep default configure data.

After any customize settings please press"Write" function to programming Dongle.

Clear Function:

To clean logs memory data in dongle.

Sensor Function:

Test the light sensor, only works if the update inside the dongle is compatible.

About the sensor testing ?

Please Check here for how to Testing.

Where to put the sensor ?

For unlocking iOS 7.x Device, the sensor position put at Some darkness place and Don't cover it on any words on Phone Screen .

Update Function:

Upgrade your dongle using selected update.

After you choose any"Operations" Options you have to update your dongle first, This request internet must connected.

20 Codes:

This codes represent about 25% of codes that people use so it might help you find the code faster in 25% of cases

Birthday Codes:

This function not enable yet

Working Status:

here are the status messages displayed for current working procedure !

Start Value:

To write your dongle start value just fill in this box.

The default setting value is 0000, E.G. if you know the passcode maybe start form 3, then you can write 3000.

This setting value also can use for when you click"Descending order" checkbox.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Format Value:

To write your dongle start Brute Force value just fill in this box.

The default setting value is FFFF, E.G. If you want to try all codes that start with 8 then adjust this to 8FFF. If you want to try codes that start with 8 and end with 4 then you can adjust this to 8FF4 and so on.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Delay Time Settings:

This usually represents the delay between codes. On iOS 7.x the delay must be at least 4300 (4.3 seconds). Please read update details for more info on what this delay represents.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Descending order Settings:

To using this function you have to setting your"Start Vlaue" at first.

Descending order which mean will send the codes like 7000 6999 6998 6997 ... etc

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Alphabet function Settings:

0123456789 is default value meaning all digits will be used.

E.G. (F Mean's will not including in unlock procedure)

Only want to try digits 6,7,8,9 , then put here FFFFFFF6789, If 0F23456789, the means once the code found, for sure 1 is not including.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Read Function:

Detect dongle settings info and the latest Code.

To use "Read" you have to connect dongle first.

Quit Function:

Exit & Close software.

Dongle Connection Status & Serial Number:

This Status showing : NOT CONNECTED | NORMAL | BOOT

Modes Using For:

NORMAL for settings / Sensor test / Read code etc.

BOOT for update and repair.

BOOT MODE you need to connect P0 and GND(P zero) pin together. Check Here For the details.

Serial Number:

Current Dongle Serial Number, Eg. 0xXXXXXXXX.

Don't share anything related aboout the serial number informations to others.

Tab Opertaions Write Sensor Update 20 Codes Start Value Status Birthday Status Alphabet Dealy Descending Read Quit Clear Status

UNLOCK IOS 7.x PHONE VIDEO

1- Update your MFC Dongle using iOS 7 V2.3 .

2- Connect the light sensor to the darkest place on the screen.

3- Swipe screen go to Emergency calling screen.(V2.2 No need)

4- Connect the cable to phone and connect MFC Dongle stat unlocking.

5- Once unlock finish the 2 of LEDs will be activing in fast blinking mode.

6- Take out the dongle and input into computer and using software to read the unlock code.

UNLOCK IOS 7.x IPAD VIDEO

The procedure as same as using V2.2 or V2.3, just plug and play .

What we need pay attention for unlocking iOS 7.x iDevice:

A. About automatically adjust iDevice brightness

Some device the Display /brightness very Lower, This will casing even your device unlocked, but dongle LED still not get fast blinking mode. So you may miss the corrected code when you unlock.

iPhone we can using iOS 7.1.2 auto v2.3 to auto adjust the brightness. But some device like iPad maybe with out SIM slot, so the problem when we unlock , we can not Go to Emergency call screen. The method can do like this:

  • Using iOS 7.1.2 auto v2.3 update your dongle at first
  • Connect your dongle (without sensor) to your device to increase the brightness
  • Using iOS 7.1.2 auto v2.2 update dongle, then start unlock

B. Sensor positons

For iOS 7.x unlocking, The sensor position very important, We have to put that at some darkness area, during unlocking we can put the kits at Light dark place. For some device maybe have different background images, if you can not be sure which area is the darkness, Just using sensor testing function to found that.


C. Failed to load update from update server ?

Normally if you get this error when you update that's because of dongle have not active or blocked on server, This you need send email to support@mfcbox.com to get help.

D. When the phone unlocked and where is the code ?

Once phone unlocked that will be go to Normal Operational Screen. this time dongle LEDs must activating fast blinking mode. otherwise the dongle will not stop work and continue sending code (usually because of sensor position not good), in this case, if you put the dongle to computer to read the code will be incorrected.

E.g. 0115 is the latest code you read via software. If the sensor did not stopped the process in time then the real code might be before that so you need to try 0114 0113 ... You can also use MFC dongle and setting the start value from 0115 (and click the descending order checkbox) and you will find the code maybe faster than trying yourself.


E. The MFC dongle tries codes one by one. When it detects change in light sensor will memorize the code so if the light sensor is not properly connected 2 cases might happen:

  • It might stop the unlock process before finding the correc code (usually if the external light influences the light sensor).
  • It might not stop the process until the user takes out the sensor or iDevice screen light getting change. (usually if it's not properly connected, or if the screen brightness is very low - Use V2.3 will auto adjustment).

Important: For iDevice iOS 7.x Unlocking, Sensor postion can not be change/Move during unlocking, Due to light sensor if detect the light value changed Dongle LEDs will activating fast blinking mode too. if this happen, please take out the dongle from OTG cable and plug back, the unlocking procedure will be contiue automatically .

INTERFACE EXPLANATION FOR iOS 8.x :

Modle & Tool Select Tab

To Unlock iOS 8.x iDevice we must choose iDevice Tab.

Operations Options:

Each options have operation guide inside the software, Read before unlock Device

iOS 8 Device - Auto v3 - v7, We Suggest using V7

Test iPower - To test your iPower Adaptor

Write Function:

Can customize your settings later or just keep default configure data.

After any customize settings please press"Write" function to programming Dongle.

Clear Function:

To clean logs memory data in dongle.

T-Mode Function:

T-Mode just for IOS 8 V6 and V7.

With 3 Smart Turbo Modes options - Test Settings Only | Auto | locked By iCloud Web.

Test Settings Only - In this mode MFC will never try to send a code to phone, will just reboot the phone as in normal operation so that you can check if all connections are good.

Auto - In this mode MFC will fist try 1 code, then will try 2 codes and so on until 5 codes. If a Phone Diabled message is encountered the dongle will decrease the number of tries each time by 1 until the message is no longer seen. This will make sure the MFC will find the codes in the fastest time possible without permanently locking the phone by mistake.

locked By iCloud Web - In this mode MFC will try codes one by one with a very long delay to wait for the unlock to complete because phones in iCloud mode respond slower to good codes.

Choose any option before you "Update" dongle, anyway you have to press"Write" function to reprogramming your dongle.

Sensor Function:

Test the light sensor, only works if the update inside the dongle is compatible.

About the sensor testing ?

Please Check here for how to Testing.

Where to put the sensor ?

For unlocking iOS 8.x Device , the sensor position put at Some lightness place and Don't cover it on any words on Phone Screen, For V7 must put on the "Stripes Pattern". but with "locked By iCloud Web" device you have to put on the message shown on the iPhone.

Update Function:

Upgrade your dongle using selected update.

After you choose any"Operations" Options you have to update your dongle first, This request internet must connected.

20 Codes:

This codes represent about 25% of codes that people use so it might help you find the code faster in 25% of cases

Birthday Codes:

This function not enable yet

Start Value:

To write your dongle start value just fill in this box.

The default setting value is 0000, E.G. if you know the passcode maybe start form 3, then you can write 3000.

This setting value also can use for when you click"Descending order" checkbox.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Format Value:

To write your dongle start Brute Force value just fill in this box.

The default setting value is FFFF, E.G. If you want to try all codes that start with 8 then adjust this to 8FFF. If you want to try codes that start with 8 and end with 4 then you can adjust this to 8FF4 and so on.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Delay Time Settings:

For iOS8 V3 V4 V5 V6 keep default 30.(V1, V2 Need setting).

For iOS8 V7 using for stop waiting to Charging battery (Per 50 Reboots).

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Descending order Settings:

To using this function you have to setting your"Start Vlaue" at first.

Descending order which mean will send the codes like 7000 6999 6998 6997 ... etc

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Alphabet function Settings:

0123456789 is default value meaning all digits will be used.

E.G. (F Mean's will not including in unlock procedure)

Only want to try digits 6,7,8,9 , then put here FFFFFFF6789, If 0F23456789, the means once the code found, for sure 1 is not including.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Read Function:

Detect dongle settings info and the latest Code.

To use "Read" you have to connect dongle first.

Quit Function:

Exit & Close software.

Dongle Connection Status & Serial Number:

This Status showing : NOT CONNECTED | NORMAL | BOOT

Modes Using For:

NORMAL for settings / Sensor test / Read code etc.

BOOT for update and repair.

BOOT MODE you need to connect P0 and GND(P zero) pin together. Check Here For the details.

Serial Number:

Current Dongle Serial Number, Eg. 0xXXXXXXXX.

Don't share anything related aboout the serial number informations to others.

Tab Opertaions Write Sensor Update 20 Codes Start Value Current status Birthday Status Alphabet Dealy Descending Read Quit Clear T-Mode Dongle status

about iDevice iOS 8.x

IDEVICE iOS 8.0 Phone Video By Auto V3 (V1-V3 Old Method):

1- Update your MFC Dongle using iOS 8 V3.

2- Connect the light sensor to the High light place on the screen.

3- Please read the operation steps on sofware

4- Once unlock finish phone will be automatically powered off.

5- Take out the dongle and input into computer and using software to read the unlock code.

FOR IDEVICE iOS 8.0-8.1 Auto Mode V4 MODE (Old Method):

V4 Mode we have add new function to display the unlock Code on the Phone Screen. The unlock Way we still using the VCC Cable to connect the Phone Battery, So Same As Auto V3

FOR IDEVICE iOS 8.0-8.1 Auto Mode V5 /TEST MODE (Old Method):

Considering some phone get "Try again in 23 million minutes" issue, we have add new method to Unlock IOS 8 Using Home automation. And also add Learning mode V5 for all customer. The connection as bellow:

V5 We need Connect the TP from Home Button To iPower Adaptor P0 Pin. And DO NOT DISCONNECT THE BATTERY OF THE PHONE. And New Version for V6 V7 the connections are same, Please continue read.


HOW TO:

- Power on the phone normally, Put sensor on high light area on the screen

- Permanently press the POWER button using a custom tool

- Connect 3 in 1 charging cable to phone and to iPower adaptor.

- Connect the TP to iPower P0 PIN.

- Connect micro usb cable to iPower adaptor

- Connect MFC Dongle to iPower adaptor and the unlock will start

IDEVICE iOS 8.0-8.1 Test Point for V5 V6 V7:

IDEVICE iOS 8.0-8.1 Test Point for V5 V6 V7:

IDEVICE iOS 8.0-8.1 Test Point for V5 V6 V7:

IDEVICE iOS 8.0-8.1 Test Point for V5 V6 V7:

How to find iDevice iOS 8.0-8.1 Test Point:

A. Power on your Device

B. Using multimeter "+" "-" , Touch one of the multimeter "-" probes(Black color) to Phone GND. Using "+" probes(Red Color) to touch the Home Button flex cable connectors pins or home button rearface welding spot. Once you saw the Device Screen start to Changing or Device Voice Control activated. Congratulations ! That's the Test Point we need to use.

How to test iDevice iOS 8.0-8.1 Test Point:

For iCloud Locked /Locked Phone you may can not see the screen change. Then you can connect our 3 in 1 cable to the Phone, same time holding Power On button, And using the Test Point Wire to Touch the 4S Connector (3 in 1) metal (Or any GND on the Phone), This can active the Screen On , If you keeping touch around 6 seconds , Phone will be reboot.


This solution should be working for iPod Touch 5 / iPad Air / iPad mini Retina ( iPad mini2 ) / iPad 4 / iPad Mini / iPad 3/ iPad2 .


Once you found , Please send related good pictures to support@mfcbox.com.
Thank's in Advance

MFC TEAM

UNLOCK iDevice iOS 8.x VIDEO

FOR IDEVICE iOS 8.x Phone Video By Auto V6 (Smart/Trubo Methods):

We recommend all customer using V7 to be more stable

A. This is the Best / Smart Way from now on

B. Can Auto Detect Passcode Attempted.

C. The algorithm Auto adjust unlock speed (Per/Reboot input code 1 ~ 5 Times)

D. Can auto detected connections are functioning

IDEVICE iOS 8.x Auto V7 Display messages info:


When using V7 screen will display the current working status as shown as the above image


V7 display the current working status info:

Code - Current Code

S - Communication Status

L - Current Sensor Value, The value must greater than 40 will work properly

- The "Stripes Pattern" is Light Sensor Position


Attention:Locked by iCloud Web iDevice will not display this working status if have "Lost Mode Messages", So sensor position must put on the "Lost Mode Messages".


Using V7 Sensor Position as shown as the above image

V7 "S" current working status (S:X):

S:1 - MFC is CHEcking connections, this is dispalyed only the first time when you connect MFC to phone.

S:2 - MFC is running normally

S:3 - The same code like last time will be sent (this usually happens after Check Connections Or when a code is found and the MFC dongle will try again one by one to confirm the code.

S:4 - An communication error (usually when the phone battery is very low) has been detected. if did not take any action MFC will reTRY in 45s.

S:7 - MFC is connected in COMputer mode will not try to send codes.

S: - Smile icon means the unlock code found, MFC will stop work.

About iOS 8.x Auto V7 How To:

1. DO NOT DISCONNECT BATTERY OF THE PHONE, and have to connect TP wire to Home Button. (Can buy a new home button to sold the TP , this way will not damage the original one. if phone already display " disabled XX minutes " need to wait until that gets out of this mode then start unlock)

2. Power on phone normally and put it into custom tool (E.g. A phone bumper case) to Permanently press POWER button , Phone will shown power off, Press Cancel.

3. Connect Micro USB to iPower adaptor. (The Charger must be 5V/1-2A, We recommend using 3 USB Port Output Power Charger .)

4. Put sensor on phone screen "Stripes Pattern" area (V7 must be here)

5. Connect HOME button TP wire to iPower Adaptor P0 PIN.

6. Connect 3 in 1 charging cable to iPower adaptor USB port.

7. Connect 3 in 1 charging cable to phone USB port.

8. Using V7 Programming MFC Dongle (This update the delay time using for waiting charging after phone reboot 50 times, and don't forget choose T-Mode option)

9. Connect MFC Dongle to iPower adaptor

10. Connect MFC Dongle to 3 in 1 cable OTG port

Wating for unlock procedure to finish.


About V7 unlock procedure please follow step by step, we suggest update dongle "Test mode" first, In this mode MFC will never try to send a code to phone, will just reboot the phone as in normal operation so that you can check if all connections are good.

What we need pay attention for unlocking iOS 8.x iDevice:

A. About automatically increase / adjustment your device brightness

For IOS8.x iDevice we will auto detect if the device need adjust the brightness, If sensor detected the value is ok , will not show the brightness adjusting icon when unlocking.


B. Sensor positons

For iOS 8.x unlocking, The sensor position is very important, We have to put that on the "Stripes Pattern" → , but for Locked by iCloud Web iDevice, sensor position must put on the "Lost Mode Messages". during unlocking please don't move the sensor, this may casing the unlock failed also phone can get disabled.


C. Phone Power Button must Permanently pressed ?

For iOS 8.x unlocking, the phone Power Button must Permanently pressed. you can using a bumper case to do this.


D. When phone getting unlocked and where is the code ?

Once phone unlocked the unlock code will be display on Phone Screen.


E. Try to input the code ?

Never try to input the code by hand if you want to try some unsure code to test if can unlock the Device, The way you can write the start value by reprogramming the Dongle and do it because if the code is wrong your Device might get disabled.

INTERFACE EXPLANATION FOR HTC :

Modle & Tool Select Tab

To Unlock HTC Device we must choose HTC Tab.

Operations Options:

All HTC Deivce using same option to update MFC Dongle

The option have operation guide inside the software, Read before unlock Device

Write Function:

Can customize your settings later or just keep default configure data.

After any customize settings please press"Write" function to programming Dongle.

Sensor Function:

For the moment, We don't use sensor to unlock, in future will add that .

Update Function:

Upgrade your dongle using selected update.

After you choose any"Operations" Options you have to update your dongle first, This request internet must connected.

20 Codes:

This codes represent about 25% of codes that people use so it might help you find the code faster in 25% of cases

Birthday Codes:

This function not enable yet

Dongle Connection Status & Serial Number:

This Status showing : NOT CONNECTED | NORMAL | BOOT

Modes Using For:

NORMAL for settings / Sensor test / Read code etc.

BOOT for update and repair.

BOOT MODE you need to connect P0 and GND(P zero) pin together. Check Here For the details.

Serial Number:

Current Dongle Serial Number, Eg. 0xXXXXXXXX.

Don't share anything related aboout the serial number informations to others.

Start Value:

To write your dongle start value just fill in this box.

The default setting value is 0000, E.G. if you know the passcode maybe start form 3, then you can write 3000.

This setting value also can use for when you click"Descending order" checkbox.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Format Value:

To write your dongle start Brute Force value just fill in this box.

The default setting value is FFFF, E.G. If you want to try all codes that start with 8 then adjust this to 8FFF. If you want to try codes that start with 8 and end with 4 then you can adjust this to 8FF4 and so on.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Delay Time Settings:

The dealy time please keep default, Don't Change.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Descending order Settings:

To using this function you have to setting your"Start Vlaue" at first.

Descending order which mean will send the codes like 7000 6999 6998 6997 ... etc

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Alphabet function Settings:

This function not enable yet

Read Function:

Detect dongle settings info and the latest Code.

To use "Read" you have to connect dongle first.

Quit Function:

Exit & Close software.

Tab Opertaions Write Sensor Update 20 Codes Start Value Currnet status Birthday Status Dealy Descending extra Read Quit Dongle Status
What we need pay attention for unlocking HTC Device:

A. How to unlock ?

1, First have to update MFC Dongle Using HTC Tab.

2, Connect 3 in 1 cable to HTC Device USB Port.

3, Connect MFC Dongle to cable OTG port.

4, Waiting unlock procedure to finish.


B. Where to put Sensor ?

For the moment unlocking HTC Device passcode, Don't need using the sensor.


C. When phone getting unlocked and where is the code ?

Once phone unlocked the Phone will be go to normal Screen, Now you can take out the dongle input to computer using MFC software to read out the code.

FAQ for unlocking HTC Device:

A. Which version and What system support ?

Only Support Android based Version 4.3+ Mobie Phones.


B. Which type of passcode can unlock ?

For the moment only support 4 digits PIN LOCK.


C. How long time will be taking for unlock ?

it will try 5 codes then wait 30 seconds while keeping the screen on about 40 seconds for 5 codes(22 hours for all 4 digits possible codes).

INTERFACE EXPLANATION FOR SAMSUNG :

Modle & Tool Select Tab

To Unlock Samsung Device we must choose Samsung Tab.

Operations Options:

All Samsung Deivce using same option to update MFC Dongle

The option have operation guide inside the software, Read before unlock Device

Write Function:

Can customize your settings later or just keep default configure data.

After any customize settings please press"Write" function to programming Dongle.

Sensor Function:

Sensor must put at darkness area on phone screen .

Update Function:

Upgrade your dongle using selected update.

After you choose any"Operations" Options you have to update your dongle first, This request internet must connected.

20 Codes:

This codes represent about 25% of codes that people use so it might help you find the code faster in 25% of cases

Birthday Codes:

This function not enable yet

Dongle Connection Status & Serial Number:

This Status showing : NOT CONNECTED | NORMAL | BOOT

Modes Using For:

NORMAL for settings / Sensor test / Read code etc.

BOOT for update and repair.

BOOT MODE you need to connect P0 and GND(P zero) pin together. Check Here For the details.

Serial Number:

Current Dongle Serial Number, Eg. 0xXXXXXXXX.

Don't share anything related aboout the serial number informations to others.

Format Value:

To write your dongle start Brute Force value just fill in this box.

The default setting value is FFFF, E.G. If you want to try all codes that start with 8 then adjust this to 8FFF. If you want to try codes that start with 8 and end with 4 then you can adjust this to 8FF4 and so on.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Delay Time Settings:

The dealy time please keep default, Don't Change.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Descending order Settings:

To using this function you have to setting your"Start Vlaue" at first.

Descending order which mean will send the codes like 7000 6999 6998 6997 ... etc

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Alphabet function Settings:

This function not enable yet

Read Function:

Detect dongle settings info and the latest Code.

To use "Read" you have to connect dongle first.

Quit Function:

Exit & Close software.

Tab Opertaions Write Sensor Update 20 Codes Start Value Format Birthday Status Dealy Descending extra Read Quit Dongle Status
What we need pay attention for unlocking Samsung Device:

A. How to unlock ?

1, First have to update MFC Dongle Using Samsung Tab.

2, Connect the light sensor to the darkest place on the screen

3, Connect 3 in 1 cable to Samsung Device USB Port.

4, Connect MFC Dongle to cable OTG port.

5, Waiting unlock procedure to finish.


B. Where to put Sensor ?

For the moment unlocking Samsung Device passcode, The sensor must be put at darkest place on phone screen.


C. When the phone unlocked and where is the code ?

Once phone unlocked that will be go to Normal Operational Screen. this time dongle LEDs must activating fast blinking mode. otherwise the dongle will not stop work and continue sending code (usually because of sensor position not good), in this case, if you put the dongle to computer to read the code will be incorrected.

E.g. 0115 is the latest code you read via software. If the sensor did not stopped the process in time then the real code might be before that so you need to try 0114 0113 ... You can also use MFC dongle and setting the start value from 0115 (and click the descending order checkbox) and you will find the code maybe faster than trying yourself.

FAQ for unlocking Samsung Device:

A. Which version and What system support ?

Only Support Android based Version 4.3+ Mobie Phones.


B. Which type of passcode can unlock ?

For the moment only support 4 digits PIN LOCK.


C. How long time will be taking for unlock ?

This update will try 5 codes then 30 seconds of waiting about 40 seconds / 5 codes(22 hours to try all codes) in some mobile phones the delay between codes will increase up to 10 seconds with more wrong codes so delay between codes must be around 10000ms(10seconds) so the waiting time will be 44 hours not 22. You must adjust the delay accordingly

INTERFACE EXPLANATION FOR MACBOOK :

Modle & Tool Select Tab

To Unlock Macbook Device we must choose Macbook Tab.

Operations Options:

You have to choose related option to update MFC Dongle

EFI Mode should be working for all Device.

The option have operation guide inside the software, Read before unlock Device

Write Function:

Can customize your settings later or just keep default configure data.

After any customize settings please press"Write" function to programming Dongle.

Sensor Function:

For the moment, this only for "EFI Boot Mode" and "iCloud custom settings" option.

Update Function:

Upgrade your dongle using selected update.

After you choose any"Operations" Options you have to update your dongle first, This request internet must connected.

20 Codes:

This codes represent about 25% of codes that people use so it might help you find the code faster in 25% of cases

Mouse Location (The function only for "iCld Custom"):

Adjust the location values of the Reboot button and the Wifi Popup Cancel if this is available. You can do it by trying values until you reach the correct location and the computer is automatically rebooted. (for example for Macbook Pro 13 inch old model the values of Reboot Button are X:565 Y:-105, Macbook Retina 13 inch the values are 556,-65) You can try other settings until you find the correct one and don't forget to share

Customer tested / shared info:

Macbook Retina 13 - X:565 Y:-105 (Reboot button)
MacBook A1370 - X:575 Y:-65 (Reboot button)
MacBook Air 13 - X:630 Y:-65 (Reboot button)

Dongle Connection Status & Serial Number:

This Status showing : NOT CONNECTED | NORMAL | BOOT

Modes Using For:

NORMAL for settings / Sensor test / Read code etc.

BOOT for update and repair.

BOOT MODE you need to connect P0 and GND(P zero) pin together. Check Here For the details.

Serial Number:

Current Dongle Serial Number, Eg. 0xXXXXXXXX.

Don't share anything related aboout the serial number informations to others.

Start Value:

To write your dongle start value just fill in this box.

The default setting value is 0000, E.G. if you know the passcode maybe start form 3, then you can write 3000.

This setting value also can use for when you click"Descending order" checkbox.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Format Value:

To write your dongle start Brute Force value just fill in this box.

The default setting value is FFFF, E.G. If you want to try all codes that start with 8 then adjust this to 8FFF. If you want to try codes that start with 8 and end with 4 then you can adjust this to 8FF4 and so on.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Delay Time Settings:

The dealy time please keep default, Don't Change.

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Descending order Settings:

To using this function you have to setting your"Start Vlaue" at first.

Descending order which mean will send the codes like 7000 6999 6998 6997 ... etc

After any customize setting value you have to press"Write" function to reprogramming your dongle.

Alphabet function Settings:

This function only for "EFI Boot Mode V2" option

Read Function:

Detect dongle settings info and the latest Code.

To use "Read" you have to connect dongle first.

Quit Function:

Exit & Close software.

Clear Function:

This function only enable for "EFI Boot Mode v2".

Tab Opertaions Write Sensor Update 20 Codes Start Value working status Birthday Status Dealy Descending Alphabet Read Quit Clear Dongle Status

UNLOCK Macbook VIDEO*

This video for MacBook EFI Unlock Method:

A. Update dongle using EFI Boot Mode

B. Write the appropriate settings using the software (the delay in milliseconds is 12000 for EFI Boot Mode) 12 seconds / code

C. Connect the light sensor to the computer in a gray area (Lock ICON) of the screen while you are in the EFI Boot Screen.

D. Once unlocking is done the dongle LEDs will start fast blinking, and Macbook will be showing different screen with Macintosh HD icon etc, Then You can read passcode from dongle by MFC software. The real unlock code is usually the one before that. So if you see 1999 then it means the real code is 1998 (Eg. Latest Guess at index 8 = 1999).

About MacBook unlocking:

A.For EFI Unlock we need press Option & Alt key (is same button) after MacBook turning on , Button must be pressed immediately after reboot before device appears the apple logo.

So when we using EFI Boot Mode unlock Macbook, you should connect the light sensor to the computer in a gray area of the screen while you are in the EFI Boot Screen.

 

B. EFI V1 and EFI V2 : V2 support arabic language also including all V1 function

 

C. iCloud custom settings

1. Connect the light sensor on the last digit displayed by the computer (in the white area of that digit).

2. Adjust the location values of the Reboot button and the Wifi Popup Cancel if this is available. You can do it by trying values until you reach the correct location and the computer is automatically rebooted. (E.G. for Macbook Pro 13 inch old model the values of Reboot Button are X:565 Y:-105, Macbook Retina 13 inch the values are 556,-65)

3. You can try other settings until you find the correct one and don't forget to share

4. The delay option is important and is depending on the speed of your computer reboot.

5. With a stopwatch you can manually use the Reboot button and calculate how many seconds are there until you are back to the iCloud pin screen. (If for example you have 34 seconds reboot time then you need to write 34000ms as delay.)

INTERFACE EXPLANATION FOR iMFC :

Modle & Tool Select Tab

To check your iDevice related info etc we must choose iMFC Tab.

Could operate 5 pieces iDevices at the same time.

First time to using iMFC must be sure the internet is connected , else will not work.

History :

To using this function required MFC Dongle connected. Here will show you connecting and connected iDevice. Double click on each line to see more information.

Here will automatic detecting iDevice information once you connect iDevice by original USB cable.

Connecting iDevice line will be showing in green color.

Date :

iDevice connection date.

Device:

iDevice model name.

Version :

iDevice detected iOS Version.

IMEI /MEID :

iDevice IMEI and MEID (sn) data

UDID / ECID :

iDevice UDID & ECID data

Jailbreak :

iDevice Jailbreak status (beta).

Mode :

Shown the status after iDevice detecting with iMFC.

Progress :

Shown the status % during iDevice operation with iMFC.

Status :

Here are the status messages displaying. same as

Backup History:

Backup the connected device history information (history.plist).

Load History:

Load the connected device history information (history.plist).

Clear History:

Empty the connected device history information (history.plist).

Credits:

Here is your remaining credits information.

Click this button will show related consumption record information.

Add:

Here you can recharge credits using recharging code.

The recharge code you can buy from official site or from reseller.

Refresh:

This function for init the device once you connect that by usb data cable

Once the Device detected, above will show up the related informations.

Check IMEI:

The function use to check the IMEI Status (Per check get result in 1-5 mins)

After job done , you can recheck the result that will be show you like this:

  • Activation Lock: ON/OFF (To show this must input Captcha)
  • Phone State: Clean / Lost/ Stolen

The credit required when you using this function (Eg. Per check cost 1 credit) .

No refund for bad requests, same imei recheck not charge credit in 24hs.

Support check status for all brand mobile phone.

Stop:

This function still in beta

Function use to stop current operations.

Progress bar:

iDevice working progress bar.

Quit Function:

Exit & Close software.

Working Status:

here are the status messages displayed for current working procedure !

Dongle Connection Status & Serial Number:

This Status showing : NOT CONNECTED | NORMAL | BOOT

Modes Using For:

NORMAL for settings / Sensor test / Read code etc.

BOOT for update and repair.

BOOT MODE you need to connect P0 and GND(P zero) pin together. Check Here For the details.

Serial Number:

Current Dongle Serial Number, Eg. 0xXXXXXXXX.

Don't share anything related aboout the serial number informations to others.

Tab history date device version imei/meid udid jailbreak mode progress status backup load clear credits add refresh check imei stop bar quit status mode and sn
About iMFC history tab functions:

A. How to connect iDevice to get info ?

1, First have to connect MFC Dongle to PC and run iMFC tab software.

2, Connect iDevice to computer by original USB cable.

3, Press "Refresh" button to detecting connected device.

4, Once done will show device info with green color in history windows.


B. Support Version & iDevice status ?

iMFC Support to readout general information for all iDevice even that disabled or Locked with user's passcode.


C. How many iDevice can detection in same time ?

iMFC Could operating 5 pieces iDevices at the same time doing different function.


D. The history will saving on MFC Server ?

No, iMFC did not save any iDevice information on Server, So your Personal information will not leak. the history saved on MFC installed folder by history.plist file(you can press "Clear history" to delete this, the operation can not reverse the data).

E. Need iTunes install & internet ?

Yes, iMFC required the latest iTunes installed on the PC (For the moment), To detect out iDevice information required internet connection.


F. Why i did not see "info" "flash" "tools" and "apps" tab ?

If did not connecting any iDevice, other tabs will not show up.


G. What's the Credits used for and why need buy credits ?

The credits using for IMEI Status Check and IPR function etc,  Those functions are not free if you want to use.


H. Where to got credits "Recharge Key" once bought online from mfcbox.com ?

The credits recharge key will be availably at your User Dashboard in 12 hours . and you need charge into your account by yourself using MFC software.


I. Credits Cost list ?

- For IMEI Status check will be cost 1 Credit for per checking.

- For IPR function the cost list you can find At here.

INTERFACE EXPLANATION FOR iMFC :

Modle & Tool Select Tab

To check your iDevice related info etc we must choose iMFC Tab.

Could operate 5 pieces iDevices at the same time.

First time to using iMFC must be sure the internet is connected , else will not work.

History :

To using this function required MFC Dongle connected. Here will show you connecting and connected iDevice. Double click on each line to see more information.

Here will automatic detecting iDevice information once you connect iDevice by original USB cable.

Connecting iDevice line will be showing in green color.

Date :

iDevice connection date.

Device:

iDevice model name.

Version :

iDevice detected iOS Version.

IMEI /MEID :

iDevice IMEI and MEID (sn) data

UDID / ECID :

iDevice UDID & ECID data

Jailbreak :

iDevice Jailbreak status (beta).

Mode :

Shown the status after iDevice detecting with iMFC.

Progress :

Shown the status % during iDevice operation with iMFC.

Status :

Here are the status messages displaying. same as

Backup History:

Backup the connected device history information (history.plist).

Load History:

Load the connected device history information (history.plist).

Clear History:

Empty the connected device history information (history.plist).

Credits:

Here is your remaining credits information.

Click this button will show related consumption record information.

Add:

Here you can recharge credits using recharging code.

The recharge code you can buy from official site or from reseller.

Refresh:

This function for init the device once you connect that by usb data cable

Once the Device detected, above will show up the related informations.

Check IMEI:

The function use to check the IMEI Status (Per check get result in 1-5 mins)

After job done , you can recheck the result that will be show you like this:

  • Activation Lock: ON/OFF (To show this must input Captcha)
  • Phone State: Clean / Lost/ Stolen

The credit required when you using this function (Eg. Per check cost 1 credit) .

No refund for bad requests, same imei recheck not charge credit in 24hs.

Support check status for all brand mobile phone.

Stop:

This function still in beta

Function use to stop current operations.

Progress bar:

iDevice working progress bar.

Quit Function:

Exit & Close software.

Working Status:

here are the status messages displayed for current working procedure !

Dongle Connection Status & Serial Number:

This Status showing : NOT CONNECTED | NORMAL | BOOT

Modes Using For:

NORMAL for settings / Sensor test / Read code etc.

BOOT for update and repair.

BOOT MODE you need to connect P0 and GND(P zero) pin together. Check Here For the details.

Serial Number:

Current Dongle Serial Number, Eg. 0xXXXXXXXX.

Don't share anything related aboout the serial number informations to others.

Tab history date device version imei/meid udid jailbreak mode progress status backup load clear credits add refresh check imei stop bar quit status mode and sn
About IMEI Status Check functions:

A. How to check IMEI Status ?

1, First have to connect MFC Dongle to PC and run iMFC tab software.

2, Press "Check IMEI" button will show checking popup window.

3, Input valid IMEI .

4, Input valid Captcha as shown.

5, Press "Check" button add checking job to server.

6, Please recheck back in few minutes by press "Check IMEI" button.


B. How long time i get result for this IMEI Check ?

Normally this will takes 1-5 mins to finish the jobs.


C. Is this check function free ?

iMFC will get 2 credits free per day. so per day you can check 2 IMEIs free. overages will be charge 1 credit for per check.


D. Where to know the checked result ?

Method A. Select checked the IMEI, and press "Check IMEI" button one more time, you will see the status be coming to "Job State : Completed", double click on it will go to "Info" tab, in this tab you can see the result.

Method B. Click on "Credits" button, you can get it in "CS" type list.

E. What is the IMEI Status ?

IMEI Status check for Black & White list report information, then you can know the device listed as lost & stolen or not.


F. The result info details for iDevice ?

  • CLEAN - FMI ON - White list and find my iPhone on
  • CLEAN - FMI OFF - White list and find my iPhone off
  • LOST/STOLEN - FMI ON - Black list and find my iPhone on
  • LOST/STOLEN - FMI OFF - Black list and find my iPhone off
  • GSM LOST - FMI ON - Gsm Lost and find my iPhone on
  • GSM LOST - FMI OFF - Gsm Lost and find my iPhone off

G. The result info details for non-iDevice ?

The result only report Deivce listed as lost & stolen & Clean or not.


H. The credtis result type details ?

To check : IMFC -> Info -> Credits.

  • REC - Recharge logs
  • IPR - IPRecovery logs
  • CS - Check IMEI logs
INTERFACE EXPLANATION FOR iMFC :

Modle & Tool Select Tab

To check your iDevice related info etc we must choose iMFC Tab.

Could operate 5 pieces iDevices at the same time.

First time to using iMFC must be sure the internet is connected , else will not work.

History :

To using this function required MFC Dongle connected. Here will show you connecting and connected iDevice. Double click on each line to see more information.

Here will automatic detecting iDevice information once you connect iDevice by original USB cable.

Connecting iDevice line will be showing in green color.

Date :

iDevice connection date.

Device:

iDevice model name.

Version :

iDevice detected iOS Version.

IMEI /MEID :

iDevice IMEI and MEID (sn) data

UDID / ECID :

iDevice UDID & ECID data

Jailbreak :

iDevice Jailbreak status (beta).

Mode :

Shown the status after iDevice detecting with iMFC.

Progress :

Shown the status % during iDevice operation with iMFC.

Status :

Here are the status messages displaying. same as

Backup History:

Backup the connected device history information (history.plist).

Load History:

Load the connected device history information (history.plist).

Clear History:

Empty the connected device history information (history.plist).

Credits:

Here is your remaining credits information.

Click this button will show related consumption record information.

Add:

Here you can recharge credits using recharging code.

The recharge code you can buy from official site or from reseller.

Refresh:

This function for init the device once you connect that by usb data cable

Once the Device detected, above will show up the related informations.

Check IMEI:

The function use to check the IMEI Status (Per check get result in 1-5 mins)

After job done , you can recheck the result that will be show you like this:

  • Activation Lock: ON/OFF (To show this must input Captcha)
  • Phone State: Clean / Lost/ Stolen

The credit required when you using this function (Eg. Per check cost 1 credit) .

No refund for bad requests, same imei recheck not charge credit in 24hs.

Support check status for all brand mobile phone.

Stop:

This function still in beta

Function use to stop current operations.

Progress bar:

iDevice working progress bar.

Quit Function:

Exit & Close software.

Working Status:

here are the status messages displayed for current working procedure !

Dongle Connection Status & Serial Number:

This Status showing : NOT CONNECTED | NORMAL | BOOT

Modes Using For:

NORMAL for settings / Sensor test / Read code etc.

BOOT for update and repair.

BOOT MODE you need to connect P0 and GND(P zero) pin together. Check Here For the details.

Serial Number:

Current Dongle Serial Number, Eg. 0xXXXXXXXX.

Don't share anything related aboout the serial number informations to others.

Tab history date device version imei/meid udid jailbreak mode progress status backup load clear credits add refresh check imei stop bar quit status mode and sn
INTERFACE EXPLANATION FOR iMFC Info:

Modle & Tool Select Tab

To check your iDevice related info etc we must choose iMFC Tab.

Info :

Here will show you connecting and connected iDevice information.

Detected info :

iDevice detected information.

Tab history info
INTERFACE EXPLANATION FOR iMFC Info:

Modle & Tool Select Tab

To check your iDevice related info etc we must choose iMFC Tab.

History :

Here will show you connecting and connected iDevice information.

Detected info :

iDevice detected information.

To Do Lists :

Some jobs required jailbreak iDeivce at first.

Please check the details in next page.

Tab history info to do list
About iMFC function for all iDevice:

A. Different color represents meaning ?

1. Green - Connecting iDevice.

2. Blue - Selected iDevice.

3. Red - Operation error.

4. Yellow - Operation finished.

5. Other without color - History record.


B. Why Jailbreak status is unknown ?

The function still in beta, only working for jailbreak phone with openSSH installed.


C. Why iMFC did not show IMEI ?

Due device with different mode or untrust with current computer, this will not show IMEI.


D. How to operation with Job function ?

1. Connect iDevice to computer by original USB cable.

2. Press "Refresh" button to detecting connected device, And choose the device.

3. At "Info" tab find related function in the job list.

4. Double Click the choosed function and following the prompts.

5. Waiting the procedure finish.


PS. Some function only support the iDevice already Jailbroken.

E. Job list ? ( With " J " Required jailbroken + Openssh installed )

1. Read info - Read iDevice related information.

2. Activate - To activate iDevice with SIM Card.

3. Deactivate - To deactivate iDevice.

4. SSH Tunnel " J " - Using USB Cable to detect phone Data via SSH.

5. Bruteforce SSH " J " - To find iDevice SSH passcode.

6. Read Account " J " - One button read iCloud account.

7. Delete Account " J " - One button delete iCloud account.

8. Start SYSlog - Read iDevice system process information.

9. Charging Cycles - Reset iDevice Charging Cycles to 0.

10. Unjailbreak " J " - Unjailbreak iDevice.

11. Change Model " J " - Change iDevice model information.

12. Hotspot ON " J " - Put iDevice Hotspot ON.

13. Hotspot OFF " J " - Put iDevice Hotspot OFF.

14. Hide Apps " J " - Hide / Show iDevice application icon.

15. Backup SHSH " J " - Backup iDevice SHSH file.

16. i4 Patch - One button bypass iCloud ID for iPhone 4.

17. Dump All " J " - Backup all iDevice data in one time.

18. iPRecovery - One button Read iCloud account and passcode .

INTERFACE EXPLANATION FOR iMFC IPR:

Modle & Tool Select Tab

To recovery your iDevice related data etc we must choose iMFC Tab.

Info :

Here will show you connecting and connected iDevice information.

IPRecovery function :

iPR function will help you recovery your iData, Please don't do anything illegal, Otherwise you need to take all responsibility.

Logs Result (Test Logs):

Shown your access data if valid.

Shown email account access if valid

Shown restrictions access if valid

Tab Info IPR logs
About IPR function for all iDevice:

A. What's IPR meaning ?

The function Support recovery iDevice iCloud (iPR) access Data details and only working with an accessible iDevice. jailbreak is not required.

The function just help you recovery your own Device data. Please don't do and not support to do anyting illegal, Otherwise you need to take all responsibility.


B. Support Versions and Conditions?

The function support all iDevices and all versions, Upto iOS 11.3.1

1. iDevice activated and accessible by screen password (Mean's can operation phone menu).

2. iCloud ID passcode didn't change yet / still valid & haven't expired.

3. iDevice's haven't encrypt by itunes (will ask passcode if you know).


C. Did not find the details will lost credits ?

No, Only get correct data details will be cost credits, Some Device will show the old data (invalid) and also no need credits.


D. How to works ?

1. Open IMFC Software.

2. Connect your iDevice to computer via USB data cable.

3. Press "Refresh" button to detect iDevice information.

4. Go to "info" tab and Click "IPRecovery" function.

5. Follow the prompting message to finish the jobs.

6. Once operation done then do related settings for iDevice.

E. During operation steps need connect iDevice to wifi /GPRS?

Keep iDevice at Airplane Mode, and no need connect to wifi/GPRS.


F. Is the activation required and disabled device support ?

No. Only support normally/accessible working iDevice.


G. Some important procedure about IPR ?

A. Device with known screen passcode : After first reboot, input screen passcode unlock the device and keeping screen on (Don't let it auto-lock)until IPR procedure finish

B. Device without screen passcode : After first reboot, Run one time IPR procedure with device, if not succeed, Then setting some screen passcode and repeat the procedure A.

About i4 Patch function - Bypass iPhone 4 iCloud:

A. What's i4 Patch meaning ?

The function Support bypass iCloud for iPhone 4 only. jailbreak on iDevice is not required.

The function just help you recovery your own Device data. Please don't do and not support to do anyting illegal, Otherwise you need to take all responsibility.


B. Support Versions and Conditions?

The function support all versions, Upto iOS 7.12.


C. This function will cost credits ?

No, this function did not cost any credits, but required at least 1 credit available in your account.


D. How to works ?

1. Open IMFC Software.

2. Connect your iDevice to computer via USB data cable.

3. Put your iDevice in DFU mode.

4. Go to "info" tab and Click "i4 Patch" function.

5. Follow the prompting message to finish the jobs.

6. Once operation done then do related settings for iDevice.

E. After bypass network can use ?

Yes, after bypass, you phone still have network if it is working deivce before bypass.

Please backup your phone UDID file (C:/MFC/iBackups/ Phone udid) to some safe place on your computer, this use for restore the network in future due some reason.


F. Is the activation required and disabled device support ?

Yes. supported. but activation required phone you may not get any network after bypass. due to activation file was lost. so activation required phone after bypass only can use as a touch.

Notice : Don't do restore or update for your device by other tools before bypass if your phone still have network, otherwise your network data will lost .


G. After using "i4 Patch" function can flash the phone ?

Yes, you can flash the phone, but you have to restore the networks data (C:/MFC/iBackups/ Phone udid) one more time


H. How to restore my phone network data ?

Connect your phone by USB data cable, Go to "info" tab , Holding computer "Shift" key and press on "i4 Patch" function, and select networks data (C:/MFC/iBackups/ Phone udid) to finish the jobs.

INTERFACE EXPLANATION FOR iMFC APPs:

Modle & Tool Select Tab

To check your iDevice related info etc we must choose iMFC Tab.

Apps :

Here can management all iDevice user's applications.

Add :

Can direct install the *.ipa application to iDevice .

List applications :

To read all applications from iDevice using this button.

List User applications :

To read all user's applications from iDevice using this button.

List System applications :

To read all system applications from iDevice using this button.

List Archives :

list all iDevice archives applications.

Operation Menu :

Can backup / upgrade / unisall all user's applications.

if restore the backup can using Add function.

Tab tools add list system archives menu user
INTERFACE EXPLANATION FOR iMFC Flash:

Modle & Tool Select Tab

To check your iDevice related info etc we must choose iMFC Tab.

Flash :

Here you can update、restore、downlowning、custom iDevice IPSW by related button.

Download Latest IPSW :

Will be automatic detecting the latest firmware and download, if already have just press "Shift" button to choose .

Update :

Update iDevice to the latest version using this button .

You can also using " shift + Click " to select the IPSW.

Restore :

Using for restore your iDevice with same version.

This required the IPSW if closed the signing.

Custom :

Allow flash the custom IPSW file.

Eg. Made addition function, ID bypass etc (Must have custom IPSW file at first, MFC did not provide any IPSW custom file for the moment).

Tab history info to do list to do list to do list
About iMFC flash page function for all iDevice:

A. About flash tab function ?

Flash function tab can Update your iDevice to the latest iOS. Also can restore your iOS iDevice to factory settings. During operation you might see an error messages. Most of these errors happen because your computer has older iTunes versions of software or can’t connect to the server.


Fix the issue :

1. Update iTunes to get the latest version of iTunes on your computer.

2. Update your OS. Can get PC software updates from the Microsoft website

3. Check your computer’s security software. You might need to update, change, disable or uninstall software that’s causing an issue.

4. Unplug extra USB devices. We always recommend plug iDevice in directly to your computer

B. Button's function ?

1. Download Latest IPSW
- Will be automatic detecting the latest firmware and download, if already have that just put into iDeviceTools folder, if already exsit in the folder will not download.

2. Update
- Update iDevice to the latest version using this button, You can also using " shift + Click " to select the IPSW.

3. Restore
- Using for restore your iDevice with same version, This required the IPSW if closed the signing.

4. Custom
- Allow flash the custom IPSW file. Eg. Made addition function, ID bypass etc (Must have custom IPSW file at first, MFC did not provide any IPSW custom file for the moment).


C. How many iDevice can support at same time ?

Could operate 5 pieces iDevices at the same time. you can doing different job with different iDevice.

INTERFACE EXPLANATION FOR iMFC Tools:

Modle & Tool Select Tab

To check your iDevice related info etc we must choose iMFC Tab.

Tools :

Here you can change or setting your iDevice Mode / time and detecting related informaion.

Mode settings :

Will be automatic put your iDevice in related mode .

Can using this function to exit any current mode .

iDevice Time :

Can read / sync / set your iDevice time .

Gernaral Actions :

Using for restart / sleep / shutdown your iDevice.

Diagnotics :

To detect out iDevice gernaral diagnotics information.

Tab tools mode time action diagnotics
INTERFACE EXPLANATION FOR Jailbreak :

Modle & Tool Select Tab

To check your iDevice related info etc we must choose jailbreak Tab.

Using this function to find iDevice passcode very fast.

Operations :

Current Bruteforce is version is 0.2.

Find Code :

To Bruteforce the passcode required the iDevice jaikbroken already and with OpenSSH application installed .

how to ?

1. Power on the iDevice .

2. Connect the iDevice via original usb data cable to PC .

3. Open software and go to Jailbreak tab (MFC Dongle must connected).

4. Press "Find Code" button then waiting iDevice reboot.

5. After iDevice reboot, you can disconnect USB cable from the iDevice.

6. Waiting iDevice finish Bruteforce the passcode .

Start Value :

If known the passcode like 8xxx, You can setting the value to be 8000 then press "Find Code".

Tab tools mode time
About Jailbreak page function for all iDevice :

About Jailbreak tab function ?

Jailbreak function can Bruteforce iDevice passcode by fast. This required your iOS iDevice already jailbroken and with OpenSSH application installed . Software also doing checking before start bruteforce, but some reason like the SSH passcode already changed the procedure will not continue.


FOR JAILBROKEN IDEVICE PASSCODE UNLOCK VIDEO:

A. Some reason will casing failed :

1. OpenSSH application not install on the iDevice .

2. iDevice OpenSSH application default passcode changed.


B. Which iOS version supported and iDevice status?

Full support all iOS 6 - iOS 8.4 Jailbroken iDevice even that in "Disabled connect to itunes" mode.


C. How many iDevice can support at same time ?

Could operate many pieces Jailbroken iDevices at the same time.


D. What can i do if OpenSSH default passcode changed ?

You can using Bruteforce SSH to check the passcode.


E. Same iDevice repeat bruteforce passcode ?

If the iDevice using MFC bruteforce passcode already and you want to repeat the procedure, you have to change the start value then start, Eg. 0000.


F. What can i do if OpenSSH default passcode changed ?

You can using Bruteforce SSH to check the passcode.

INTERFACE EXPLANATION FOR HUAWEI:

What can do here ?

To working with your Device related functions.

History :

Here will show you connecting and connected Device information.

Detected info :

Device detected information.

To Do Lists :

Please check the details in next page.

Tab history info to do list
About huawei supported functions:

A. How to connect HuaWei Device to get info ?

1, Connect Device to computer by original USB cable.

2, On Device input code " *#*#2846579#*#* ", and Choose Project Menu -> Background settings -> USB ports settings -> Manufacture mode.

3, Press "Refresh" button to detecting connected device.

4, Once done will show device info with green color in history windows.


B. Support Version & Device status ?

Support to readout general information for all Huawei Android Hisilicon based phones Device.


C. Credits Cost list ?

The cost list you can find At here.


PS. Some function will cost credits, but will let you know before you confirm, if the operation failed or something happened like phone battery finish during procedure etc, the credits will be automatic back to your acount after few minutes .

E. Job list ? ( With " Credits " Required Credits )

1. Read info - Read Device related information.

2. Authorize " Credits " - To authorize Device by hw unlocker server.

3. Finder OFF " Credits " - To unlock/remove account ID.

4. Simlock Check - To check the simlock status.

5. FBlock Check - To check the Fastboot status.

6. FBlock OFF " Credits " - One button unlock Fastboot.

7. FBlock ON " Credits " - One button lock Fastboot.

8. Root Check - Read Device Root status.

9. Root ON " Credits " - One button lock Root.

10. Root OFF " Credits " - One button unlock Root.

11. Factory Reset - One button do Factory Reset.

12. Customer Reset - One button do Customer Reset.



PS. After you press "AUTHORIZE" button you can do all other functions without cost, means just cost one time credits. But if you did not press "AUTHORIZE" button, Each function which you try to use will cost different credits. .

INTERFACE EXPLANATION FOR MFC Tools :

Modle & Tool Select Tab

To read mfc dongle sn and calculator iOS8 iDevice delay time etc we must choose mfc tools Tab.

Dongle management :

Current you can read MFC Dongle Serial number by press "Read SN".

Don't share or post MFC Dongle SN information on public internet.

Help Link :

The useful & help URL link for MFC Dongle .

iOS 8 delay time calculator:

Calculator for iOS8 iDevice unlock delay time settings - Stop waiting charging.

how to ?

1. Power on the iDevice .

2. Using "iOS 8 V7 Test Mode" and connecting iDevice start to test, and recording the battery percentage. Eg.90%.

3. Once iDevice reboot you can Using stopwatch start to counting the Reboot times. Eg. 30 seconds.

4. Let iDevice reboot 10 times, We check again the battery Used percentage and record. Eg. 3%.

5. Disconnect the MFC Dongle, Now waiting iDevice battery charging and recording the Charging Time and Charge percentage. Eg. 15 minutes / 2% .

6. Put the value into related box and press "Calculate" button , software will Calculator a delay value .

7. Put the value into delay time setting box and programming MFC Dongle then back to unlock .

Tab tools mode time

SHP - Product Description

Smart Heating Platform (SHP) is the best professional toolkit for your electronic hardware repair needs. It offers many indispensable functions and makes working in a professional repair shop much more easy.

  • - All functions are finely controlled using our custom made software control system with real time data display
  • - General settings and operating ambient temperature ranges can be programmed using our software in order to work with or without computer
  • - Has 4 integrated temperature sensors (internal temperature, heater temperature, external temperature and real time temperature tester K Type sensor)
  • - The heating system has automatic temperature control that can keeping temperature constant and accurate while you work
  • - An integrated 4 digits LED Display that can display all necessary data including state, temperature and voltages
  • - A built in temperature tester function that can accurately and efficiently measure solder iron and hot air temperature (Measurement range: -125 - 1200 ℃, Tolerance: ± 1 ℃) in real time . This way you can be sure your rework tools are correctly calibrated and working at peak performance
  • - Heating panel A made from high purity copper with an efficient method for high heat flux design
  • - Heating panel B made from aluminum can separating glass etc(Compatible size for 13 inch and below)
  • - With panel B can use for baking、drying、aging etc (Eg.water-flooded components of UMT mainboard)
  • - Almost all current PCB integrated circuits can be soldered and de-soldered without the need of a soldering iron or a hot air gun. (Eg,Apple A7 A8 A9 A10 CPU 、baseband IC or harddisk IC etc)

SHP - Product Description

  • - Can act as a pre-heater for your everyday needs to minimize the risk of component damage
  • - Smart phones, iPad products's glass lens, touch screens & LCD displays can be separated in a few mins
  • - Default factory settings with general working conditions specification (Eg. Glue remove、IC de-soldering & Soldering、lens & touch screen assembly settings etc)
  • - All functions are user customizable
  • - Integrated self-resetting overheat protection,LED warning alerts and sound alerts,Voltage overload protection,Short circuit detection and automatic shutdown function integrated etc.
  • - Lifetime free software upgrades and more(Working with all Apple product and Huawei Android Mobile Hisilicon based mobile device (Called iMFC)

Technical Data:

  • Operating voltage: AC 220V & DC 5V(USB)
  • Output Power: 300W
  • Temperature Range:Room temperature - 350 ℃
  • Temperature Tolerance: ± 3 ℃
  • SHP Box Size: 226*90*45 MM
  • Heating panel A Size: 58*12 MM ; B Size: 315*220 MM

System Requirements:

  • All Windows XP, Windows 7, Windows 8/8.1 or Windows 10

Safety and Technical notes:

    • - The ground wire assembly must be connected from the controller ground stud to a ture earth groud.
    • - An electric accurately heater is a much safer source than an iron or air gun. However, the heaters also get hot and must be handled with care.

Create & Active account

① First you must Register an account on official website with valid Email.(MFC User Skip this step can direct login)


Once you done, you will got this message:

You have successfully registered. Please check your email for further information!

Verify your account (MFC User Skip this step)

② Verify your account withToken code (This code will be received by email)


A. Go to your email inbox. you will got this :

B. Input your registered email and the Token code to activate your account:

Login to website

③ Once your account activated, then you can go to login page access to site.

If you lost your passcode you can using "Lost passcode" function to find the passcode back. The related code will be send to you by register email

Activation SHP BOX

To activation your box you have to know the serial number at first, to get the serial number info you can following this.

A. Normally On Package with a lable on side have the Serial Number (0xXXXXXXXX)

B. If you using old version then connect box to computer, Run Software go to settings and Press "Update" you will see the serial number via logs

Activation Page

Now go to User Dashboard and at Activation SHP tab , input sHP Serial number, Press "Activating Now" button to active box.


After activated SHP online, you have to wait 1-5 mins then can login by SHP software. If SHP Box have not activate that will be effect box update and normal use.

Download & Install

Download software

Go to download page to get software and install it. [ Due customer computer have different antivirus software, You may close before then install and add that into trust list. ]

Install software

① When you finish downloaded the sfotware from download page , Now start to install it. The installing will be automatic finish once get your confirm during in procedure.

Install software

② The software will installing to C:/SHP, you can change the path to D:/SHP etc. but the folder path must be like this (C:/SHP or D:/SHP) otherwise maybe not work.
Install software

  ③ Continue installing
Install software

  ④ During installing the drivers will be automatic installed. just press "next" button let it automatic finish. (Installed path C:/MFC/Driver/DongleDrivers)

Install software

⑤ Driver Installing... (Installed path C:/MFC/Driver/MicrosoftRedistributables. For windows 7, if you have Dll error, you have to manually install both driver  ["vcredist_x64.exe" / "vcredist_x86.exe"] in this folder again. )

Install software

⑥ Software Install Done.
About INSTALL FAQ:

Got mfc120.dll ,mfc120u.dll and libusb0.dll error ?

a, Install drivers from DongleDrivers directory (C:/MFC) by running InstallDriver.exe This will installing mfc120.dll & mfc120.dll required for the program to start.

b, Install vcredist_x86 or vcredist_x64 for windows from MicrosoftRedistributables directory (Win 7 Need install Both)

c, Frist time to use software you need Connect SHP in BOOT MODE(Press and holding BSS button on the box then connect USB cable). This will installing libusb0.dll driver required for the program to start.

 

We encourage all customers always to upgrade the spftware to the latest version , When the new version released on official website , the old version will be expired after few days. Once software expired you can not use that anymore.


How to Check 220V if Connected to ground ?

a, Connect power cable to AC220 port

b, Switch on the red "Heater Power" button

c, If red "Heater Power" button lED brightness too dark, Please double check the ground wire or just connect the yellow cable (in the packing) to ground

d, If red "Heater Power" button lED brightness enough mean's ground connected

Boot Mode - First time using SHP need install libusb0.dll driver.
About SHP Normal & Boot Mode
  • NORMAL MODE Can use software all functions etc.
  • BOOT MODE Use for SHP update / repair. Need holding and press BSS Button and then connect to USB cable let the SHP box go to Boot Mode

View the details in device manager

If everything setup correctly you will see like this

SHP Showing - Front and Back

SHP Showing - Control Info:

A. USB LED Light ?

When USB cable connected this LED will be turn on.

Button info:

B. Fan LED light ?

Heater Fan & Box Fan use for downgrade the temperature, When SHP box at shutdown or temperature downgrade mode will be turn on , Box fan default always keeping off mode but when boxself temperature rise up more than 41 degrees will be automatice turn on.

C. BSS Button ?

BBS button can working with Boot & Start & Stop & Shutdown multifunction etc. Boxslef knows the current mode and when you press that will be automatic switch to other mode etc, If press time more than 2 seconds will be go to shutdown mode (Same time the heater fan will be trun on).

D. Setup Button ?

Setup button and switch which temperature you want to display on the 4 digits screen and setting working mode when you working without computer.

E. High & Low LED light ?

After usb cable connected, Low LED light will be trun on( The means Heating panel A with lower temperature and safe to touch), After start heating the high LED light will be trun on, and if Heating panel A temperature more than 41 degrees will always trun on.

F. Up & Down Button ?

Working with BBS button and Setup Button to display the data, Eg,Setting working mode without computer etc .

G. Heating & Danger LED light ?

When heating the LED will be trun on and blinking, both LEDs have same function for the moment

About SHP Software - Main:

Device Connect Status

Connect Status:

Normal Mode.

Boot Mode.

Not Connect Mode.

Device Working Status:

Working Status:

Waiting Mode.

Working Mode.

Shutdown Mode.

Fan Status:

Box and Heater fan use for cooling, When cooling or shutdown mode the heater fan will be start work, Once boxself detect temperature higher than 41 degrees will be start and default mode always off.

USB Current voltage:

Here will be display the current voltage when shp connect to any 5v USB Power(Can from PC or USB hub etc),Once the voltage lower than 4.8 will effect box performances.

Internal Temp & Heating Status:

Here will display box internal temperature and heating status.

Operation Settings:

List all factory and customize settings,once you choose one of that then can press start button to apply the setting.

Temp Adjustment:

Adjust range is between taget and maximum temp, once you adjust then can press start button to apply the setting.

Heater Temp & Status:

To display the plate A current temperature value.

External Temp & Status:

To display the plate B current temperature value, You have to connect extra sensor to plate B, Otherwise is 0.

K Temp & Status:

To display current temperature of the tested carrier,Use for test or calibration for iron or hot air temperature.

Start:

When press this button, SHP will start to work.

Waiting:

When press this button, SHP will be stay in waiting mode.

Shutdown:

To cooling the box use this button, And press "BSS" button on the box have same function(but you have to using software to start box if you want to use).

Connect status shp status fan USB status iner Temp options Adjust Temp Temp E-Temp K-Temp start stop shutdown
About Main FAQ::

A. How to start work on SHP ?

1, Using USB Data cable connect shp to computer.

2, Input 220V power( Make sure power was ground at work environment, Otherwise using the yellow wire connect to ground).

3, Open SHP software, Choose operation setting, then press start button.

4, SHP start to work, Due high temperature must be handled with care.


B. How long can reach to target temperature ?

Base work environment temperature, We tested when room temperature is 34 degrees to reach 300 degrees need 3 mins 28 seconds.


C. How to quickly cool?

Operation method, directly on the device press "BSS" key or press "Shutdown" button in the software platform, the platform is starting to cool. During cooling process Heater Fan LED will light up, Heater fan will start work, please don't block the fan exhaust opening affecting cooling. Cooling time is usually 3 times of normal temperature up to the target temperature, Eg: 300 degrees to room temperature time in about 10 minutes .


PS. Did not touch the plate area in the condition of high temperature , there is a risk of burns .

D. USB port is not enough to use, can use an external USB ?

Can use an external USB, after setup and just press the start button then you can unplug the USB cable, directly into the 5v on the USB extension, SHP platform will continue to work on my current mode (And you can also setup this using "BSS" and "SETUP" button on BOX) .


E. Why always mention about grounding & how to judgement, what will be effected?

As part of the customer's work environment is using a two phase alternating current (ac), thus grounding line actual no grounding in the three pin plug. But SHP's heater power switch (Red) can detect whether grounded. When SHP Connected 220V, switch on heater Power Button, if there is a ground, red switch on the LED light is very bright, Otherwise is very dark. Conversely work environment is not grounded, not only to the maintenance of electronic parts can be damaged, If in the event of leakage, because there is no ground current can be discharged into the earth that the personnel get an electric shock will be happened.

About SHP Software - settings:

Update

Update Options:

V1-Default firmware settings.

V2-To test all LEDs and Fans.

V6-The newest firmware settings.

After choose one of that please click apply and waiting box automatic update in boot mode(If not going to boot, you can disconnect USB cable and holding "BSS" button then plug USB cable that update will be resume), this required input your username and passcode from mfcbox.com.

General settings:

Currnet some function still in beta

Factory Settings:

Press this button will be reset to factory setting, Customize settings will be reset too.

Load Settings:

Can use shared file from others.

Save Settings:

Can save as a data file about current settings.

Memorize Settings:

Can memorize the setting into SHP Box for all the customize setting.

New:

Add new customize setting.

Delete:

Choose one of setting then can delete from list.

About list settings:

The list data for each are HEK values(H: Plate A temp, E: Plate B temp, K: Test temp).

Target & Maximum temperature mean's Want to achieve the temperature of the target value but not over the maximum,the current work temperature can be adjustment between this range

When customize settings please besure target and maximum value correct

update settings factory USB status iner Temp options Adjust Temp Temp E-Temp
About SHP Settings::

A. How to update SHP Box?

1, Using USB Data cable connect shp to computer.

2, Make sure the computer with internet connection.

3, Open SHP software, input your username and password then go to settings and choose Vx option in the list, after this click on apply and waiting SHP upgrade finish in boot mode (You can go to logs to check the update result).

4, During update don't disconnect USB Data Cable.


B. Why need connect to server update ?

Any software there may be had some unknown bugs, when got customer feedback about this, we can fix bug in the fastest time to upgrade, and online update is the most practical and the fastest way to do this.


C. I am using the latest version ?

During update server will tell you if that's the latest version.


PS. 220V power not necessarily need when update.

D. How to customize the settings ?

At settings tab press "New" button to add new customize setting, parameters can customize too.

Then you can choose and apply the settings at main option tab.

Press "Memorize settings" can save current setting data into box


E. Factory reset ?

Click "Factory settings" button will restore factory Settings data for SHP, customize options will be erased at the same time, suggest save Settings before restore, and this operation can not reverse .


F. Loading & Save settings ?

Can use shared file from others and can save as a data file about current settings then share to others.


iREWORK

iREWORK - Table of Contents

iREWORK is using the new heat conduction technology, this is the leading transfer heat method which guaranty to the customer The best quality alongside the utmost safety. iREWORK is the best professional toolkit for your electronic hardware repair needs. It offers many indispensable functions and makes working in a professional repair shop much more easy.


    • ● Warnings and precautions
      • ○ Safety precautions

    • ● Specifications
      • ○ Product Technical specifications

    • ● Package content
      • ○ Packing list / Unpacking

    • ● Operating Modes
      • ○ LED Indicators
      • ○ Buttons Functions
      • ○ LED Shown Informations
      • ○ Fast Install /Starting

    • ● Software Operate
      • ○ System Requirements
      • ○ Software Interface / FAQ

Warnings and precautions

The iREWORK is not intended for use by persons (including children) with reduced physical, sensorial or mental capabilities. As well, persons with lack of experience and knowledge, unless they have been given supervision or training concerning use of the soldering station by a person responsible for their safety.


  • ● Do not touch the heating while operating the iREWORK
  • ● Do not use the iREWORK near flammable items
  • ● Make sure that the heating plate not touch any object while in operating mode it’s negatively affects the heating ramp up sensitivity.
  • ● Use in a well-ventilated work space and preferably use an External cooling Fan
  • ● Connect only to properly grounded outlets to prevent risk of electric shock or equipment malfunction

Safety precautions

  • ● Use the protective gloves to exchange the PCB into the PCB’s fixture and do not expose or touch either the PCB or fixture by your skin
  • ● Keep a distance from the working space during the rework process, reworking process might produce unwanted smoke toward your eyes and lungs

iREWORK - Specifications

Product Technical specifications


  • Ambient Operating Temperature - 0 - 50°C
  • Maximum Enclosure Temperature - 52°C
  • Input Line voltage - 230VAC / 50 & 60Hz
  • Output voltage - 3.3-12VAC
  • Power Consumption - 300Watts max.
  • Heating Ramp up (indoor temperatures 28°C) - 1°C/sec.
  • Cooling down ratio (indoor temperatures 28°C) - 0.45°C/sec.
  • Material - Aluminum /Copper/Plastic /Glass
  • Thermocouples - K type external
  • Thermal recovery - 0.11 sec
  • Dimensions (L*W*H) mm - 230*90*45
  • Package size (L*W*H) mm - 350*280*100
  • Heating Plate (L*W*H) mm - 315*220*5

iREWORK - Package content

Package list


  • 1 x iREWORK BOX
  • 1 x Universal PCB holder(PCB fixture)
  • 1 x Wide plate
  • 1 x Silicone Protective pad
  • 1 x ESP cable
  • 1 x Repair tools kit
  • 1 x Potective sleeve (Red Color)
  • 1 x Scaper (Yellow Color)
  • 1 x Cleaning Brush
  • 1 x Power Cable
  • 1 x Ground cable
  • 1 x AB USB Cable

More details
https://www.mfcbox.com/shop/irework

iREWORK - Unpacking


  • ● STEP 1 Unpack the iREWORK and make sure all parts included in the packing list is on the package
  •   
  • ● STEP 2 Place and arrange the iREWORK with all other parts in a convenient location in your workspace
    • 2.1 Download the Software control program from official website, install the program and drivers
  •   
  • ● STEP 3 Plug the power cord into electricity supply and switch on the iREWORK
    • 3.1 Connect the USB cable and open the software start to work (iREWORK also support working without computer)

iREWORK - Operating Modes

The iREWORK control panel with OLED type that's multi colors and seen from many view angels with bright fonts to make display is very comfortable and convenient.


iREWORK

iREWORK - Operating Modes

LED Indicators


  • iREWORKPower on/off led indicator is the V220
  • iREWORKMain Led indicator: box cooling fan (programmed speed during process – Full speed at Idle state)
  • iREWORKBox Led indicator: secondary cooling fan (user and hardware safety cooling fan programmed to keep internal temperature less than 52 degrees)
  • iREWORKSafe led indicator: light on when heating plate temperature less 50 degrees, when it is off indicates danger to touch the heating plate as precautions. Also, in boot mode will be on.
  • iREWORKHeating led indicator: indicates the heater operating algorithm, light on when start heating.

iREWORK - Operating Modes

Buttons Function


  • iREWORK
  • This button have Start / Stop / Shutdown and Boot function
  • ● Short press one time will be function for Start / Stop 1 second
  • ● Long press one time will be function for Shutdown 2 to 3 seconds
  • ● Power on box while holding ‘F’, iREWORK will go to boot mode.
  • iREWORK
  • This button have setting / confirm / quite function
  • ● Short press one time can choose operation option by press ‘▲’ ‘▼’
  • ● Long press one time can adjust temperature by press ‘▲’ ‘▼’
  • ● Once adjusted temperature or changed options need press one time ‘S’ to confirm settings, if don't save setting press one time ‘F’ to quite
  • iREWORK
  • ● Button working with Button ‘S’ and also can working standard, By default can holding and press ‘▲’ to check the current target temperature settings
  • ● Power on box while holding ‘▲’ will show box serial number / firmware version information
  • iREWORK
  • ● Button working with Button ‘S’ and also can working standard, By default can holding and press ‘▼’ to check the current settings, like Fans settings, next procedure info etc.

iREWORK - Operating Modes

LCD Shown information


  • iREWORK
  • ● Serial number and Firmware version.

  • iREWORK
  • 50Hz/60Hz current frequency
  • 3.xxV actual voltage for control
  • H is the heating temperature
  • Bt is box temperature
  • Hp heater power rate, If not work show OFF
  • Op the selected profile & option number
  • T is K type tip temperature reader
  • E is extra Thermocouple temperature readings use for seperate Screen by wide plate, this need connect ESP)
  • WAIT the process not started, ended or idle state, If process are running will show ‘WORKING’
  • No other action next procedure and time information

iREWORK - Operating Modes

LCD Shown information


iREWORK

Short press button ‘S’ one time can choose/change operation option by press ‘▲’ ‘▼’

  • SETUP - 6 current operation option
  • H 260<265 current heater ‘target’ < ‘maximum’ temperature
  • Remove A10 CPU current operation description

iREWORK

Long press button ‘S’ one time can adjust target temperature by press ‘▲’ ‘▼’

  • Adjust H current operation heater option
  • Target 260 current heater target temperature, this temperature can not be more than maximum

Ps. Once adjusted temperature or changed options need press one time ‘S’ to confirm settings, if don't save setting press one time ‘F’ to quite

iREWORK - Operating Modes

LCD Shown information


iREWORK

Holding and press button ‘▲’ to check the current operation option heating temperature and Extra temperature settings(Only Options 1 with Extra temperature)


iREWORK

Holding and press button ‘▼’ to check the current settings, like Fans settings, next procedure info etc

iREWORK - Fast install


iREWORK

Ps. Make sure that the PCB fixture (PCB universal holder) mounted over the heating plate correctly and conducted with each other’s with no gaps or warpage and fit together with 2 piece M2*6 screws

iREWORK - Fast Starting


iREWORK

● Press ‘S’ button, Choose the operating profile from 2 to 7 preprogrammed profiles, select option by press ‘▲’ ‘▼’ , To confirm the option by Press ‘S’ button, then press button ‘F’ box will start to working

● When the target temperature reached the unit buzzer will beep twice

● Start to remove the glue by the removal tool first until all area around adjacent component is clean. Dig (gently and slowly) underneath the chip. Start pull up from one side once the Chip moves

Ps. USING FORCE WILL RESULTS DAMAGE OF THE CHIP OR THE PCB LAND OR CONNECTION

iREWORK - Fast install


iREWORK

INSTALL STEPS

iREWORK - Fast install


Display replace introduction?


Follow the steps in this guide to replace the display Screen (Eg, iPad Rro Screen 12.9):

● Preparing the opening tools kit on the table from iREWORK package

● Install the Wide plate / Esp cable / Protective pad as left 'INSTALL STEPS' shown

● Select operation profile 1 option from box (or software)

● Press 'F' button from box (or 'START' button from software) to start heating

● Waiting reach to target temperature < 85°

● Waiting 1-60 seconds once buzzer beep

● Taking the tools start to disassembly


Ps. During disassembly do not pivot the display screen that will break the flex cables

iREWORK - Software operate

iREWORK software is used for a variety of purposes: to support datalogger programming, enable communication between iREWORK and computers to deployment and control work process, manage data files, and display data in graphical formats. More advanced users can customize the working processes to be more intelligent while using.

iREWORK

iREWORK - Software operate

Operating system requirements ?

● 2gb of RAM

● C++ windows components 2015

● All Windows 7, Windows 8/8.1 or Windows 10

● Disable the Antivirus (some of files will be deleted)


Software Download ?

Software always avaliable download from official page at : https://www.mfcbox.com/downloads


Software Installation ?

Run the installation/unpack package to C: / directory it should be C: / iREWORK or D: / iREWORK.


How to ?

Power on the iREWORK, connect to PC using the USB cable. Run iREWORK.exe that will detect the unit ID and activation status. Each step will be shown in logs box.

iREWORK - SOFTWARE Main:

Heating Status:

The graphs indicator shows current heating status

Temperature rame up is 1°C/sec (indoor 28°C)

Maintain Status:

The graphs indicator shows target temperature

When reach the target temperature will start maintaining the process

Target temperature:

Target Graphs

Indicator shows the selected operation options value

Cooling Status:

Indicator shows the cooling download graphs

Fan will be automatic start, temperature down ratio is 0.45°C/sec (indoor 28°C)

K-Temp (K-Tester) Status:

Indicator shows the thermometer current temperature of the tested carrier,Use for test or calibration for iron or hot air temperature.

During heating or cooling this will be effect a lit but it's normal

Internal Temp:

For iREWORK internal temperature value. Normally less than 52°C, else iREWORK will switch to shutdown mode.

External Temp:

Indicator shows the operation option 1 current temperature value, You have to connect ESP cable and also attched the wide palte on iREWORK

Device Connect Status

  • Not Ready - When unit not connected or not power on
  • Waiting - When unit connected successfully
  • Working - When process are running
  • Boot Mode - When unit update
  • Shutdown - When process are cooling
  • Disconnected - When unit manually power off or USB disconnect

Operation Settings:

Press to select the process profile

List all factory and customize settings,once you choose one of that then can press start button to apply the setting.

Heater & External Settings:

Here will display heater & External temperature settings once you select the options.

External temperature only for option 1.

Heater temperature can manually set up but can not more than maximun settings.

Heater temperature can keep current value by press 'KEEP' button.

StART:

Press to start and run a process.

KEEP:

Press to keep the current heater temperature and maintaining status.

STOP:

Press to stop the running process.

SHUTDOWN:

Press to end running process

Long time press 'F' button on the box have same function(but you have to using software to start box or swich off/on box again if you want to use).

Heater Temp:

Indicator shows the heating temperature value

External Temp:

Indicator shows operation option 1 temperature value

K Temp:

Indicator shows the External thermocouple (K-Tester) temperature value

Internal Temp:

Indicator shows unit internal temperature value

Clear:

Press to remove the plotted graph

Logs Informations:

All operation step logs will display here

Status info:

Normally here will show server connection status

Serial Number:

Indicator shows unit serial number

Heating Status Maintain Status Target temperature Cooling Status K-Temp (K-Tester) Status Internal Temp External Temp Device Connect Status Operation Settings Heater & External Settings start keep STOP shutdown Heater Temp External Temp K Temp Internal Temp Clear Logs Informations Status info Serial Number
iREWORK - SOFTWARE Settings:

Factory Settings:

Apply factory default setting

The action will case the cutomize settings reset

Load Settings:

load settings from your PC or download ones

The *.plist profile can take from other customer shared.

Save Settings:

Save the current settings to your PC

The *.plist profile save customize settings.

Share to other people to use if with perfect tested

Memorize Settings:

Programming the customize settings to box.

If didn't programme to box , once software restart the customize setting will reset to default

if apply factory default setting this will reset.

Update & Authorize:

Authorizes and validate iREWORK

Advance update in boot mode : Power on box while holding button‘F’, when start updating release button ‘F’

New:

Create new process profile setting.

And setup TH & MTH.

Delete:

Delete to replace exist ones

Select one or more of setting then delete from list.

Description:

Shows the programmed process profiles includes all parameters for profile description (process name)

TH:

Targeted heater temperature for the process

Target temperature value can not more than MTH (Maimmum Heater Temperature)

TE:

Targeted External temperature for the process

Target external temperature value can not more than MTE (Maimmum External Temperature)

For the moment this only for profile 1 - Separate Screen option

MTH:

Maimmum Heater Temperature

Maximum limits for the targeted temperature should be set for process or measurement safety

MTE:

Maimmum External Temperature

Maximum limits for the targeted temperature should be set for process or measurement safety

For the moment this only for profile 1 - Separate Screen option

Timeout:

Timeout in seconds, '0'is default settings

This settings will let the iREWORK to continue with the current process

The action will be start when heater reach the target temperature

Can working closely together with 'Type' & 'Jump' functions

Type:

What action of the perform after timeout has expired, So this depending on 'Timeout' settings

STOP - Current process will end

SHUTDOWN - Current process will end and Box will going to SHUTDOWN

JUMP - Current process will end and Jump to next action , if did not setup 'JUMP' function will automactic go to stop

Jump:

If you have selected 'JUMP' in 'Type' then you need to specify what settings is the next one after timeout has expired

factory settings Load settings save settings Memorize settings Update & Authorize new delete description TH TE MTH MTE Timeout Type Jump

iREWORK - Software FAQ

Internet Required ?

● Normal Operation - NO

● Update & Authorize - YES

iREWORK


ESP Problem ?

● Need connect ESP cable

● Only process profile 1 need connect ESP by default settings


How to know control system working good ?

● iREWORK have real-time monitoring systems are in place to ensure safety

● Any error will show on the OLED screen


Should setting TE and MTE when customize ?

● Usually no need if you don't use the wide plate to do heating operation


iPOWER X

iPOWER X

iPOWER X is high precision DC to DC power supply, technical grade designed for scientific research, product development, laboratories, schools and electronic production lines. The output voltage and current are continuously adjustable at nominal value. Featuring high accuracy, reliability, perfect overload and short circuit protection circuit, they can be an ideal choice for the mobile phone repair industry.

Specifications:
  • - Device performance is ensured by a 16 MHz CPU clock frequency and enhanced characteristics which include robust I/O, independent watchdogs and a clock security system.
  • - LCD Display Panel Accuracy is within ± 2.5%
  • - 1.5 inch LCD displaying accurate voltage, ampere, electric quantity measuring values and related settings.
  • - The controls are easy to use featuring a rotary switch that acts as an ON/OFF button in the same time. Voltage and Current can be monitored in the same time. Separate power on button for Apple devices.
  • - Input: DC barrel (+ centered) DC 5 - 24V / 2.5 - 3A (Recommended input voltage 5V ( 2A iPad charger), 19.5V (4A laptop charger))
  • - Output: DC 0.3 - 18V / 0.1 - 3A Continuously adjustable, output can be maximum input voltage + 0.6V
  • - Voltage regulation/Ripple and noises: CV < ± 0.2V, CC < ± 0.2A
  • - Protection for battery ports: High current limiting, short circuit protection, reverse polarity protection, 4.3V max output hardware protection
  • - Protection for jack output: High current limiting, short circuit protection
  • - Two operational modes: constant voltage and constant current with max limits working in the same time. Once the max current will be reached the voltage will drop to keep the current constant.

iPOWER X

Product Features:

  • - Mobile phone battery simulator ports (4 USB output port (DC 4.2V / 0.5 - 3A ) specially for Apple mobile phone, used together with supplied cables will enable the use of iPOWER X to simulate battery connection. The mobile phone battery simulator ports are hardware limited to 4.3V to protect against accidental voltage settings that might damage the device. They also have reverse voltage protection in case of wrong connections. Current can be limited continuously from 0 to 3A so that the user can track down short circuit in devices by monitoring board temperature. The mobile phone battery ports also control an 5V 200mA output design to simulate power on so can be used with bare boards without connected power on buttons. Integrated Apple battery IC will enable the correct display of battery information in Apple devices.
  • - Jack output (RED + , BLACK GND) - Enables the user to supply devices other than mobile phone boards, current and voltage limited.
  • - Voltage tester input - Integrated voltage tester input (Yellow) will display the measured voltage on the main display once the tester is connected to the device not requiring a separate voltage tester. The device can be powered using the main battery connectors and only one wire will be required to test voltages on the device.
  • - Computer control input - On the back of iPOWER X there is a special connector to enable easy control of the voltages and other functions using a computer. Just connect the provided PC cable and start the iPOWER X software. iPOWER X can be also easily calibrated this way for more precise readings.

iPOWER X - Control Panel

iPOWER X BOX PANEL

iPOWER X - Operating Modes

SET / ON Button Function

  • iPOWER X SET and On Button

  • SET - Button with Set ampere & voltage function
  • ● Short press one time and holding - LCD Display will Show "V" or "A"
  • ● Using Rotary Switch Button adjust related output value.
  • ● While adjusting LCD Display will Show Current & Customize value.
  • ● Adjusted output value will automatic save into Box.

  • ON - Button with USB automatic Power On 、 Factory Reset & Boot function
  • Factory Reset
  • ● Once Input Power connected, Short press one time (1-2s) iPOWER X will do factory reset.
  • ● During factory reseting LCD Display will Show 4.2/2.5 etc.
  • USB automatic Power On
  • ● Output Voltage < 4.3 - Short press one time USB port Power will be enable.
  • Boot Mode
  • ● Used only when iPOWER X Box need Upgrading.
  • ● Holding this button and Connect Input power.
  • ● Connect PC Cable then do update by iPOWER X Software.

iPOWER X - Operating Modes

POWER Button Function

  • iPOWER X Rotary Switch Button
  • Power Button - With Rotary Switch and On/Off function
  • ● Short press one time will On/Off Output Power
  • ● Coordinate with Red "SET" Button adjust related output value.

TEST Jack Function

  • iPOWER X Test Jack
  • TEST Jack - Measure voltage function
  • ● Plug the Test Cable into this JACK
  • ● Connect device to iPOWER X and Power On
  • ● Using Test Cable measure related components voltage of the device.

Jack Output Function

  • iPOWER X Jack output
  • Jack Output - Enables the user to supply devices other than mobile phone boards
  • ● Output current and voltage adjustable
  • ● RED + / BLACK GND & -.

iPOWER X - How is WORK

Connect DC Power Cable
  • Step 1
  • ● Connect Input DC Power Cable to iPOWER X DC Jack
  • ● DC barrel (+ centered) DC 5 - 24V / 2.5 - 3A (Recommended input voltage 5V ( 2A iPad charger), 19.5V (4A laptop charger))

iPOWER X - How is WORK

Connect Data Cable
  • Step 2
  • ● Connect 2 in 1 Data Cable to iPOWER X USB Port

iPOWER X - How is WORK

Connect DC Input Power
  • Step 3
  • ● Connect iPOWER X to DC Power Supply via DC Cable, DC barrel (+ centered) DC 5 - 24V / 2.5 - 3A (Recommended input voltage 5V ( 2A iPad charger), 19.5V (4A laptop charger))

iPOWER X - How is WORK

Connect Data Cable
  • Step 4
  • ● Connect the Flex connector Cable to Phone Board.
  • ● Usually do this test before the Repaired board assembly.

iPOWER X - How is WORK

Enable Output Power
  • Step 5
  • ● Press down the "POWER" button (Rotary) to switch on/off.
  • ● Output Voltage < 4.3, the Green LED will lighten.

iPOWER X - How is WORK

Power On Board
  • Step 6
  • ● Press down "ON" button to Power On the Board.

iPOWER X - How is WORK

Power On Board and Measure
  • Step 7
  • ● Once the board have Power you can measure the components voltage value by "Test Cable", and also can track down short circuit in devices by monitoring board temperature etc.

Help links ?

1. Official Website - http://www.mfcbox.com.

2. English Forum - http://forum.gsmhosting.com.

3. Chinese Forum - http://www.gsmhosting.cn.

4. Software Download - http://www.mfcbox.com.

5. Youtube Video - https://www.youtube.com.


Email support ?

Send Email To: support@mfcbox.com.